View LT1933ES6TRPBF_4834225.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

lt1933 1 1933fe typical application features applications description 600ma, 500khz step-down switching regulator in sot-23 and dfn packages the lt ? 1933 is a current mode pwm step-down dc/dc converter with an internal 0.75a power switch, packaged in a tiny 6-lead sot-23. the wide input range of 3.6v to 36v makes the lt1933 suitable for regulating power from a wide variety of sources, including unregulated wall transformers, 24v industrial supplies and automotive batteries. its high operating frequency allows the use of tiny, low cost inductors and ceramic capacitors, resulting in low, predictable output ripple. cycle-by-cycle current limit provides protection against shorted outputs, and soft-start eliminates input current surge during start up. the low current (<2a) shutdown provides output disconnect, enabling easy power manage- ment in battery-powered systems. l , lt, ltc, ltm, linear technology and the linear logo are registered trademarks of linear technology corporation. thinsot is a trademark of linear technology corporation. all other trademarks are the property of their respective owners. 3.3v step-down converter n wide input range: 3.6v to 36v n 5v at 600ma from 16v to 36v input n 3.3v at 600ma from 12v to 36v input n 5v at 500ma from 6.3v to 36v input n 3.3v at 500ma from 4.5v to 36v input n fixed frequency 500khz operation n uses tiny capacitors and inductors n soft-start n internally compensated n low shutdown current: <2a n output adjustable down to 1.25v n low pro? le (1mm) sot-23 (thinsot?) and (2mm 3mm 0.75mm) 6-pin dfn packages n automotive battery regulation n industrial control supplies n wall transformer regulation n distributed supply regulation n battery-powered equipment ef? ciency v in 4.5v to 36v off on 0.1f 22h 1n4148 mbrm140 10k 16.5k 22f 1933 ta01a 2.2f v out 3.3v/500ma v in boost gnd fb shdn sw lt1933 load current (ma) 0 90 95 300 400 1933 ta01b 85 80 100 200 600 500 75 70 65 efficiency (%) v in = 12v v out = 5v v out = 3.3v
lt1933 2 1933fe absolute maximum ratings input voltage (v in ) ..................................... C0.4v to 36v boost pin voltage ...................................................43v boost pin above sw pin .........................................20v shdn pin ................................................... C0.4v to 36v fb voltage .................................................... C0.4v to 6v operating temperature range (note 2) lt1933e ...................................................C40c to 85c (note 1) top view fb gnd shdn boost v in sw dcb package 6-lead (2mm 3mm) plastic dfn 4 5 7 6 3 2 1 ja = 73.5c/w, jc = 12c/w exposed pad (pin 7) is gnd, must be soldered to pcb boost 1 gnd 2 fb 3 6 sw 5 v in 4 shdn top view s6 package 6-lead plastic tsot-23 ja = 165c/w, jc = 102c/w pin configuration order information lead free finish tape and reel part marking package description temperature range lt1933idcb#pbf lt1933idcb#trpbf lcgm 6-lead (2mm 3mm) plastic dfn C40c to 125c lt1933hdcb#pbf lt1933hdcb#trpbf lcgn 6-lead (2mm 3mm) plastic dfn C40c to 150c lt1933es6#pbf lt1933es6#trpbf ltagn 6-lead plastic tsot-23 C40c to 85c lt1933is6#pbf lt1933is6#trpbf ltagp 6-lead plastic tsot-23 C40c to 125c lt1933hs6#pbf lt1933hs6#trpbf ltddq 6-lead plastic tsot-23 C40c to 150c lead based finish tape and reel part marking package description temperature range lt1933idcb lt1933idcb#tr lcgm 6-lead (2mm 3mm) plastic dfn C40c to 125c lt1933hdcb lt1933hdcb#tr lcgn 6-lead (2mm 3mm) plastic dfn C40c to 150c lt1933es6 lt1933es6#tr ltagn 6-lead plastic tsot-23 C40c to 85c lt1933is6 lt1933is6#tr ltagp 6-lead plastic tsot-23 C40c to 125c lt1933hs6 lt1933hs6#tr ltddq 6-lead plastic tsot-23 C40c to 150c consult ltc marketing for parts speci? ed with wider operating temperature ranges. for more information on lead free part marking, go to: http://www.linear.com/leadfree/ for more information on tape and reel speci? cations, go to: http://www.linear.com/tapeandreel/ lt1933i .................................................. C40c to 125c lt1933h ................................................ C40c to 150c maximum junction temperature lt1933e, lt1933i ................................................. 125c lt1933h ............................................................... 150c storage temperature range .................. C65c to 150c lead temperature, s6 package (soldering, 10 sec) ............................................ 300c
lt1933 3 1933fe electrical characteristics note 1: stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. exposure to any absolute maximum rating condition for extended periods may affect device reliability and lifetime. note 2: the lt1933e is guaranteed to meet performance speci? cations from 0c to 70c. speci? cations over the C40c to 85c operating temperature range are assured by design, characterization and correlation with statistical process controls. the lt1933i speci? cations are parameter conditions min typ max units undervoltage lockout 3.35 3.6 v feedback voltage l 1.225 1.245 1.265 v fb pin bias current v fb = measured v ref + 10mv (note 4) l 40 120 na quiescent current not switching 1.6 2.5 ma quiescent current in shutdown v shdn = 0v 0.01 2 a reference line regulation v in = 5v to 36v 0.01 %/v switching frequency v fb = 1.1v 400 500 600 khz v fb = 0v 55 khz maximum duty cycle l 88 94 % switch current limit (note 3) 0.75 1.05 a switch v cesat i sw = 400ma, s6 package i sw = 400ma, dcb6 package 370 370 500 mv mv switch leakage current 2a minimum boost voltage above switch i sw = 400ma 1.9 2.3 v boost pin current i sw = 400ma 18 25 ma shdn input voltage high 2.3 v shdn input voltage low 0.3 v shdn bias current v shdn = 2.3v (note 5) v shdn = 0v 34 0.01 50 0.1 a a the l denotes the speci? cations which apply over the full operating temperature range, otherwise speci? cations are at t a = 25c. v in = 12v, v boost = 17v, unless otherwise noted. (note 2) guaranteed over the C40c to 125c temperature range. the lt1933h speci? cations are guaranteed over the C40c to 150c temperature range. note 3: current limit guaranteed by design and/or correlation to static test. slope compensation reduces current limit at higher duty cycle. note 4: current ? ows out of pin. note 5: current ? ows into pin.
lt1933 4 1933fe typical performance characteristics ef? ciency, v out = 5v ef? ciency, v out = 3.3v switch current limit maximum load current maximum load current switch voltage drop feedback voltage undervoltage lockout switching frequency load current (ma) 0 80 90 100 300 400 1933 g01 70 100 200 600 500 60 efficiency (%) v in = 24v v in = 12v t a = 25c v out = 5v d1 = mbrm140 l1 = toko d53lcb 33 h load current (ma) 0 80 90 100 300 400 1933 g02 70 100 200 600 500 60 efficiency (%) v in = 24v v in = 12v v in = 5v t a = 25c v out = 3.3v d1 = mbrm140 l1 = toko d53lcb 22 h duty cycle (%) 0 switch current limit (ma) 600 800 1200 1000 80 1933 g03 400 200 0 20 40 60 100 minimum typical t a = 25c input voltage (v) 0 load current (ma) 600 700 20 1933 g04 500 400 5 10 15 30 25 800 l = 22 h l = 33 h t a = 25c v out = 5v input voltage (v) 0 load current (ma) 600 700 20 1933 g05 500 400 5 10 15 30 25 800 l = 22 h l = 15 h t a = 25c v out = 3.3v switch current (a) 0 0 switch voltage (mv) 100 200 300 400 600 500 0.2 0.4 1933 g06 0.6 0.1 0.3 0.5 t a = 85c t a = 25c t a = C40c temperature (c) feedback voltage (v) 1.260 1.255 1.250 1.240 1.230 1.245 1.235 1933 g07 C50 C25 0 25 50 75 100 150 125 temperature (c) uvlo (v) 3.8 3.6 3.4 3.2 3.0 1933 g08 C50 C25 0 25 50 75 100 150 125 temperature (c) switching frequency (khz) 600 550 500 450 400 1933 g09 C50 C25 0 25 50 75 100 150 125
lt1933 5 1933fe typical performance characteristics frequency foldback soft-start shdn pin current typical minimum input voltage typical minimum input voltage switch current limit operating waveforms operating waveforms, discontinuous mode fb pin voltage (v) 0.0 switching frequency (khz) 700 600 300 100 400 500 200 0 0.5 1933 g10 1.0 1.5 t a = 25c shdn pin voltage (v) 0 switch current limit (a) 1.4 1.2 0.6 0.2 0.8 1.0 0.4 0 1 1933 g11 234 t a = 25c dc = 30% 0 shdn pin current ( a) 200 150 50 100 0 4 1933 g12 81216 shdn pin voltage (v) t a = 25c load current (ma) 5 input voltage (v) 6 7 8 1933 g13 4 v out = 5v t a = 25c l = 33 h to start to run 1 10 100 load current (ma) 4.5 input voltage (v) 5.0 5.5 6.0 1933 g14 3.0 3.5 4.0 v out = 3.3v t a = 25c l = 22 h to start to run 1 10 100 temperature (c) C50 switch current limit (a) 1.4 1.2 1.0 0.6 0 0.2 0.8 0.4 C25 0 25 1933 g15 50 75 100 150 125 v in = 12v, v out = 3.3v, i out = 400ma, l = 22 h, c out = 22 f 1933 g16 v out 10mv/div i l 200ma/div v out1 1.8v v out2 1.2v v sw 10v/div v in = 12v, v out = 3.3v, i out = 20ma, l = 22 h, c out = 22 f 1933 g17 v out 10mv/div i l 200ma/div v out1 1.8v v out2 1.2v v sw 10v/div
lt1933 6 1933fe pin functions boost (pin 1): the boost pin is used to provide a drive voltage, higher than the input voltage, to the internal bipolar npn power switch. gnd (pin 2/pin 5 and exposed pad, pin 7): tie the gnd pin to a local ground plane below the lt1933 and the circuit components. return the feedback divider to this pin. fb (pin 3/pin 6): the lt1933 regulates its feedback pin to 1.245v. connect the feedback resistor divider tap to this pin. set the output voltage according to v out = 1.245v (1 + r1/r2). a good value for r2 is 10k. shdn (pin 4): the shdn pin is used to put the lt1933 in shutdown mode. tie to ground to shut down the lt1933. tie to 2.3v or more for normal operation. if the shutdown feature is not used, tie this pin to the v in pin. shdn also provides a soft-start function; see the applications infor- mation section. v in (pin 5/pin 2): the v in pin supplies current to the lt1933s internal regulator and to the internal power switch. this pin must be locally bypassed. sw (pin 6): the sw pin is the output of the internal power switch. connect this pin to the inductor, catch diode and boost capacitor. (sot-23/dfn) block diagram r driver q1 s osc slope comp frequency foldback int reg and uvlo v c g m 1.245v 1933 bd q q boost sw fb r2 r1 v out l1 d2 c3 c1 d1 v in c2 v in on off gnd c4 r3 shdn
lt1933 7 1933fe operation (refer to block diagram) the lt1933 is a constant frequency, current mode step down regulator. a 500khz oscillator enables an rs ? ip- ? op, turning on the internal 750ma power switch q1. an ampli? er and comparator monitor the current ? owing between the v in and sw pins, turning the switch off when this current reaches a level determined by the voltage at v c . an error ampli? er measures the output voltage through an external resistor divider tied to the fb pin and servos the v c node. if the error ampli? ers output increases, more current is delivered to the output; if it decreases, less cur- rent is delivered. an active clamp (not shown) on the v c node provides current limit. the v c node is also clamped to the voltage on the shdn pin; soft-start is implemented by generating a voltage ramp at the shdn pin using an external resistor and capacitor. an internal regulator provides power to the control cir- cuitry. this regulator includes an undervoltage lockout to prevent switching when v in is less than ~3.35v. the shdn pin is used to place the lt1933 in shutdown, dis- connecting the output and reducing the input current to less than 2a. the switch driver operates from either the input or from the boost pin. an external capacitor and diode are used to generate a voltage at the boost pin that is higher than the input supply. this allows the driver to fully saturate the internal bipolar npn power switch for ef? cient opera- tion. the oscillator reduces the lt1933s operating frequency when the voltage at the fb pin is low. this frequency foldback helps to control the output current during startup and overload. applications information fb resistor network the output voltage is programmed with a resistor divider between the output and the fb pin. choose the 1% resis- tors according to: r1 = r2(v out /1.245 C 1) r2 should be 20k or less to avoid bias current errors. reference designators refer to the block diagram. input voltage range the input voltage range for lt1933 applications depends on the output voltage and on the absolute maximum rat- ings of the v in and boost pins. the minimum input voltage is determined by either the lt1933s minimum operating voltage of ~3.35v, or by its maximum duty cycle. the duty cycle is the fraction of time that the internal switch is on and is determined by the input and output voltages: dc = (v out + v d )/(v in C v sw + v d ) where v d is the forward voltage drop of the catch diode (~0.4v) and v sw is the voltage drop of the internal switch (~0.4v at maximum load). this leads to a minimum input voltage of: v in(min) = (v out + v d )/dc max C v d + v sw with dc max = 0.88 the maximum input voltage is determined by the absolute maximum ratings of the v in and boost pins and by the minimum duty cycle dc min = 0.08 (corresponding to a minimum on time of 130ns): v in(max) = (v out + v d )/dc min C v d + v sw note that this is a restriction on the operating input voltage; the circuit will tolerate transient inputs up to the absolute maximum ratings of the v in and boost pins. inductor selection and maximum output current a good ? rst choice for the inductor value is: l = 5 (v out + v d ) where v d is the voltage drop of the catch diode (~0.4v) and l is in h. with this value the maximum load current will be above 500ma. the inductors rms current rating must be greater than your maximum load current and its
lt1933 8 1933fe applications information table 1.inductor vendors vendor url part series inductance range (h) size (mm) coilcraft www.coilcraft.com d01608c 10 to 22 2.9 4.5 6.6 mss5131 10 to 22 3.1 5.1 5.1 mss6122 10 to 33 2.2 6.1 6.1 sumida www.sumida.com cr43 10 to 22 3.5 4.3 4.8 cdrh4d28 10 to 33 3.0 5.0 5.0 cdrh5d28 22 to 47 3.0 5.7 5.7 toko www.toko.com d52lc 10 to 22 2.0 5.0 5.0 d53lc 22 to 47 3.0 5.0 5.0 wrth elektronik www.we-online.com we-tpc mh 10 to 22 2.8 4.8 4.8 we-pd4 s 10 to 22 2.9 4.5 6.6 we-pd2 s 10 to 47 3.2 4.0 4.5 saturation current should be about 30% higher. for robust operation in fault conditions the saturation current should be ~1a. to keep ef? ciency high, the series resistance (dcr) should be less than 0.2. table 1 lists several vendors and types that are suitable. of course, such a simple design guide will not always re- sult in the optimum inductor for your application. a larger value provides a slightly higher maximum load current, and will reduce the output voltage ripple. if your load is lower than 500ma, then you can decrease the value of the inductor and operate with higher ripple current. this allows you to use a physically smaller inductor, or one with a lower dcr resulting in higher ef? ciency. there are several graphs in the typical performance characteristics section of this data sheet that show the maximum load current as a function of input voltage and inductor value for several popular output voltages. low inductance may result in discontinuous mode operation, which is ok, but further reduces maximum load current. for details of maximum output current and discontinuous mode opera- tion, see linear technology application note 44. finally, for duty cycles greater than 50% (v out /v in > 0.5), there is a minimum inductance required to avoid subharmonic oscillations. choosing l greater than 3(v out + v d ) h prevents subharmonic oscillations at all duty cycles. catch diode a 0.5a or 1a schottky diode is recommended for the catch diode, d1. the diode must have a reverse voltage rating equal to or greater than the maximum input voltage. the on semiconductor mbr0540 is a good choice; it is rated for 0.5a forward current and a maximum reverse voltage of 40v. the mbrm140 provides better ef? ciency, and will handle extended overload conditions. input capacitor bypass the input of the lt1933 circuit with a 2.2f or higher value ceramic capacitor of x7r or x5r type. y5v types have poor performance over temperature and ap- plied voltage, and should not be used. a 2.2f ceramic is adequate to bypass the lt1933 and will easily handle the ripple current. however, if the input power source has high impedance, or there is signi? cant inductance due to long wires or cables, additional bulk capacitance may be necessary. this can be provided with a low performance electrolytic capacitor. step-down regulators draw current from the input sup- ply in pulses with very fast rise and fall times. the input capacitor is required to reduce the resulting voltage ripple at the lt1933 and to force this very high frequency
lt1933 9 1933fe applications information switching current into a tight local loop, minimizing emi. a 2.2f capacitor is capable of this task, but only if it is placed close to the lt1933 and the catch diode; see the pcb layout section. a second precaution regarding the ceramic input capacitor concerns the maximum input voltage rating of the lt1933. a ceramic input capacitor combined with trace or cable inductance forms a high quality (under damped) tank circuit. if the lt1933 circuit is plugged into a live supply, the input voltage can ring to twice its nominal value, possibly exceeding the lt1933s voltage rating. this situation is easily avoided; see the hot plugging safely section. output capacitor the output capacitor has two essential functions. along with the inductor, it ? lters the square wave generated by the lt1933 to produce the dc output. in this role it determines the output ripple, and low impedance at the switching frequency is important. the second function is to store energy in order to satisfy transient loads and stabilize the lt1933s control loop. ceramic capacitors have very low equivalent series re- sistance (esr) and provide the best ripple performance. a good value is c out = 60/v out where c out is in f. use x5r or x7r types, and keep in mind that a ceramic capacitor biased with v out will have less than its nominal capacitance. this choice will provide low output ripple and good transient response. transient performance can be improved with a high value capacitor, but a phase lead capacitor across the feedback resistor r1 may be required to get the full bene? t (see the compensation section). high performance electrolytic capacitors can be used for the output capacitor. low esr is important, so choose one that is intended for use in switching regulators. the esr should be speci? ed by the supplier, and should be 0.1 or less. such a capacitor will be larger than a ceramic capacitor and will have a larger capacitance, because the capacitor must be large to achieve low esr. table 2 lists several capacitor vendors. table 2.inductor vendors vendor phone url part series comments panasonic (714) 373-7366 www.panasonic.com ceramic, polymer, tantalum eef series kemet (864) 963-6300 www.kemet.com ceramic, tantalum t494, t495 sanyo (408) 749-9714 www.sanyovideo.com ceramic, polymer, tantalum poscap murata (404)436-1300 www.murata.com ceramic avx www.avxcorp.com ceramic, tantalum tps series taiyo yuden (864)963-6300 www.taiyo-yuden.com ceramic
lt1933 10 1933fe applications information figure 1 shows the transient response of the lt1933 with several output capacitor choices. the output is 3.3v. the load current is stepped from 100ma to 400ma and back to 100ma, and the oscilloscope traces show the output volt- age. the upper photo shows the recommended value. the second photo shows the improved response (less voltage drop) resulting from a larger output capacitor and a phase lead capacitor. the last photo shows the response to a high performance electrolytic capacitor. transient performance is improved due to the large output capacitance, but output ripple (as shown by the broad trace) has increased because of the higher esr of this capacitor. figure 1. transient load response of the lt1933 with different output capacitors as the load current is stepped from 100ma to 400ma. v in = 12v, v out = 3.3v, l = 22h. 22f fb 16.5k 10k v out 1933 f01a v out 50mv/div i out 200ma/div v out 50mv/div i out 200ma/div fb v out 1933 f01b 16.5k 10k 22f 2x 470pf v out 50mv/div i out 200ma/div sanyo 4tpb100m fb 1933 f01c v out + 16.5k 10k 100f
lt1933 11 1933fe applications information boost pin considerations capacitor c3 and diode d2 are used to generate a boost voltage that is higher than the input voltage. in most cases a 0.1f capacitor and fast switching diode (such as the 1n4148 or 1n914) will work well. figure 2 shows two ways to arrange the boost circuit. the boost pin must be at least 2.3v above the sw pin for best ef? ciency. for outputs of 3v and above, the standard circuit (figure 2a) is best. for outputs between 2.5v and 3v, use a 0.47f capacitor and a small schottky diode (such as the bat-54). for lower output voltages the boost diode can be tied to the input (figure 2b). the circuit in figure 2a is more ef- ? cient because the boost pin current comes from a lower voltage source. you must also be sure that the maximum voltage rating of the boost pin is not exceeded. the minimum operating voltage of an lt1933 application is limited by the undervoltage lockout (~3.35v) and by the maximum duty cycle as outlined above. for proper startup, the minimum input voltage is also limited by the boost circuit. if the input voltage is ramped slowly, or the lt1933 is turned on with its shdn pin when the output is already in regulation, then the boost capacitor may not be fully charged. because the boost capacitor is charged with the energy stored in the inductor, the circuit will rely on some minimum load current to get the boost circuit running properly. this minimum load will depend on input and output voltages, and on the arrangement of the boost circuit. the minimum load generally goes to zero once the circuit has started. figure 3 shows a plot of minimum load to start and to run as a function of input voltage. in many figure 2. two circuits for generating the boost voltage figure 3. the minimum input voltage depends on output voltage, load current and boost circuit v in boost gnd sw v in lt1933 (2a) d2 1933 f02a v out c3 v boost C v sw ? v out max v boost ? v in + v out v in boost gnd sw v in lt1933 (2b) d2 1933 f02b v out c3 v boost C v sw ? v in max v boost ? 2v in load current (ma) 4.5 input voltage (v) 5.0 5.5 6.0 1933 f03a 3.0 3.5 4.0 v out = 3.3v t a = 25c l = 22h to start to run 1 10 100 load current (ma) 5 input voltage (v) 6 7 8 1933 f03b 4 v out = 5v t a = 25c l = 33 h to start to run 1 10 100 minimum input voltage v out = 3.3v minimum input voltage v out = 5v
lt1933 12 1933fe applications information cases the discharged output capacitor will present a load to the switcher which will allow it to start. the plots show the worst-case situation where v in is ramping very slowly. for lower start-up voltage, the boost diode can be tied to v in ; however, this restricts the input range to one-half of the absolute maximum rating of the boost pin. at light loads, the inductor current becomes discontinu- ous and the effective duty cycle can be very high. this reduces the minimum input voltage to approximately 300mv above v out . at higher load currents, the inductor current is continuous and the duty cycle is limited by the maximum duty cycle of the lt1933, requiring a higher input voltage to maintain regulation. soft-start the shdn pin can be used to soft-start the lt1933, reducing the maximum input current during start up. the shdn pin is driven through an external rc ? lter to create a voltage ramp at this pin. figure 4 shows the start up waveforms with and without the soft-start circuit. by choosing a large rc time constant, the peak start up current can be reduced to the current that is required to regulate the output, with no overshoot. choose the value of the resistor so that it can supply 60a when the shdn pin reaches 2.3v. figure 4. to soft-start the lt1933, add a resistor and capacitor to the shdn pin. v ini = 12v, v out = 3.3v, c out = 22f, r load = 10 run 5v/div v out 5v/div i in 100ma/div run shdn gnd 1933 f04a 50s/div run 5v/div v out 5v/div i in 100ma/div run 15k 0.1f shdn gnd 1933 f04b 0.5ms/div
lt1933 13 1933fe applications information shorted and reversed input protection if the inductor is chosen so that it wont saturate exces- sively, an lt1933 buck regulator will tolerate a shorted output. there is another situation to consider in systems where the output will be held high when the input to the lt1933 is absent. this may occur in battery charging ap- plications or in battery backup systems where a battery or some other supply is diode or-ed with the lt1933s output. if the v in pin is allowed to ? oat and the shdn pin is held high (either by a logic signal or because it is tied to v in ), then the lt1933s internal circuitry will pull its quiescent current through its sw pin. this is ? ne if your system can tolerate a few ma in this state. if you ground the shdn pin, the sw pin current will drop to essentially zero. however, if the v in pin is grounded while the output is held high, then parasitic diodes inside the lt1933 can pull large currents from the output through the sw pin and the v in pin. figure 5 shows a circuit that will run only when the input voltage is present and that protects against a shorted or reversed input. hot plugging safely the small size, robustness and low impedance of ceramic capacitors make them an attractive option for the input bypass capacitor of lt1933 circuits. however, these capaci- tors can cause problems if the lt1933 is plugged into a live supply (see linear technology application note 88 for a complete discussion). the low loss ceramic capacitor combined with stray inductance in series with the power source forms an under damped tank circuit, and the voltage at the v in pin of the lt1933 can ring to twice the nominal input voltage, possibly exceeding the lt1933s rating and damaging the part. if the input supply is poorly controlled or the user will be plugging the lt1933 into an energized supply, the input network should be designed to prevent this overshoot. figure 5. diode d4 prevents a shorted input from discharging a backup battery tied to the output; it also protects the circuit from a reversed input. the lt1933 rns only when the input is present v in boost gnd fb shdn sw d4 v in lt1933 1933 f05 v out backup d4: mbr0540
lt1933 14 1933fe applications information figure 6. a well chosen input network prevents input voltage overshoot and ensures reliable operation when the lt1933 is connected to a live supply + + lt1933 2.2f v in 20v/div i in 5a/div 20s/div v in closing switch simulates hot plug i in (6a) (6b) (6c) low impedance energized 24v supply stray inductance due to 6 feet (2 meters) of twisted pair + + lt1933 2.2f 10f 35v ai.ei. lt1933 2.2f 0.1f 1 1933 f06 v in 20v/div i in 5a/div 20s/div v in 20v/div i in 5a/div 20s/div danger! ringing v in may exceed absolute maximum rating of the lt1933
lt1933 15 1933fe applications information figure 6 shows the waveforms that result when an lt1933 circuit is connected to a 24v supply through six feet of 24-gauge twisted pair. the ? rst plot is the response with a 2.2f ceramic capacitor at the input. the input voltage rings as high as 35v and the input current peaks at 20a. one method of damping the tank circuit is to add another capacitor with a series resistor to the circuit. in figure 6b an aluminum electrolytic capacitor has been added. this capacitors high equivalent series resistance damps the circuit and eliminates the voltage overshoot. the extra capacitor improves low frequency ripple ? ltering and can slightly improve the ef? ciency of the circuit, though it is likely to be the largest component in the circuit. an alterna- tive solution is shown in figure 6c. a 1 resistor is added in series with the input to eliminate the voltage overshoot (it also reduces the peak input current). a 0.1f capacitor improves high frequency ? ltering. this solution is smaller and less expensive than the electrolytic capacitor. for high input voltages its impact on ef? ciency is minor, reducing ef? ciency less than one half percent for a 5v output at full load operating from 24v. frequency compensation the lt1933 uses current mode control to regulate the output. this simpli? es loop compensation. in particular, the lt1933 does not require the esr of the output capaci- tor for stability allowing the use of ceramic capacitors to achieve low output ripple and small circuit size. figure 7 shows an equivalent circuit for the lt1933 control loop. the error amp is a transconductance ampli? er with ? nite output impedance. the power section, consisting of the modulator, power switch and inductor, is modeled as a transconductance ampli? er generating an output cur- rent proportional to the voltage at the v c node. note that the output capacitor integrates this current, and that the capacitor on the v c node (c c ) integrates the error ampli- ? er output current, resulting in two poles in the loop. r c provides a zero. with the recommended output capacitor, the loop crossover occurs above the r c c c zero. this simple model works well as long as the value of the inductor is not too high and the loop crossover frequency is much lower than the switching frequency. with a larger ceramic capacitor (very low esr), crossover may be lower and a phase lead capacitor (c pl ) across the feedback divider may improve the phase margin and transient response. large electrolytic capacitors may have an esr large enough to create an additional zero, and the phase lead may not be necessary. if the output capacitor is different than the recommended capacitor, stability should be checked across all operating conditions, including load current, input voltage and tem- perature. the lt1375 data sheet contains a more thorough discussion of loop compensation and describes how to test the stability using a transient load. figure 7. model for loop response C + C + 1.245v sw v c lt1933 gnd 1933 f07 r1 out esr error amplifier current mode power stage fb r2 500k r c 100k c c 80pf c1 c1 g m = 150mhos g m + c pl 0.7v 1.1mho
lt1933 16 1933fe applications information pcb layout for proper operation and minimum emi, care must be taken during printed circuit board layout. figure 8 shows the recommended component placement with trace, ground plane and via locations. note that large, switched currents ? ow in the lt1933s v in and sw pins, the catch diode (d1) and the input capacitor (c2). the loop formed by these components should be as small as possible and tied to system ground in only one place. these components, along with the inductor and output capacitor, should be placed on the same side of the circuit board, and their connections should be made on that layer. place a local, unbroken ground plane below these components, and tie this ground plane to system ground at one location, ideally at the ground terminal of the output capacitor c1. the sw and boost nodes should be as small as possible. finally, keep the fb node small so that the ground pin and ground traces will shield it from the sw and boost nodes. include two vias near the gnd pin of the lt1933 to help remove heat from the lt1933 to the ground plane. figure 8a shows the layout for the dfn package. vias near and under the exposed die attach paddle minimize the thermal resistance of the lt1933. figure 8. a good pcb layout ensures proper, low emi operation gnd v out vias v in 1933 f08a d1 c1 c2 shutdown vias outline of local ground plane v in v out 1933 f08b system ground c2 d1 c1 (8a) dfn package (8b) sot-23 package
lt1933 17 1933fe typical applications 3.3v step-down converter 12v step-down converter v in 4.5v to 36v off on c3 0.1f d2 l1 22h r2 10k r1 16.5k c1 22f 6.3v 1933 ta02b c2 2.2f v out 3.3v/ 500ma v in boost gnd fb shdn sw lt1933 d1 v in 14.5v to 36v off on c3 0.1f d3, 6v d1 l1 47h r2 10k r1 86.6k c1 10f 1933 ta02d c2 2.2f v out 12v/ 450ma d2 v in boost gnd fb shdn sw lt1933
lt1933 18 1933fe package description dcb package 6-lead plastic dfn (2mm 3mm) (reference ltc dwg # 05-08-1715) 3.00 0.10 (2 sides) 2.00 0.10 (2 sides) note: 1. drawing to be made a jedec package outline m0-229 variation of (tbd) 2. drawing not to scale 3. all dimensions are in millimeters 4. dimensions of exposed pad on bottom of package do not include mold flash. mold flash, if present, shall not exceed 0.15mm on any side 5. exposed pad shall be solder plated 6. shaded area is only a reference for pin 1 location on the top and bottom of package 0.40 0.10 bottom viewexposed pad 1.65 0.10 (2 sides) 0.75 0.05 r = 0.115 typ r = 0.05 typ 1.35 0.10 (2 sides) 1 3 6 4 pin 1 bar top mark (see note 6) 0.200 ref 0.00 C 0.05 (dcb6) dfn 0405 0.25 0.05 0.50 bsc pin 1 notch r0.20 or 0.25 45 chamfer 0.25 0.05 1.35 0.05 (2 sides) recommended solder pad pitch and dimensions 1.65 0.05 (2 sides) 2.15 0.05 0.70 0.05 3.55 0.05 package outline 0.50 bsc
lt1933 19 1933fe information furnished by linear technology corporation is believed to be accurate and reliable. however, no responsibility is assumed for its use. linear technology corporation makes no representa- tion that the interconnection of its circuits as described herein will not infringe on existing patent rights. package description s6 package 6-lead plastic sot-23 (reference ltc dwg # 05-08-1634) 1.50 C 1.75 (note 4) 2.60 C 3.00 0.25 C 0.50 typ 6 plcs note 3 datum a 0.09 C 0.20 (note 3) s6 sot-23 0502 2.80 C 3.10 (note 4) 0.95 bsc 1.90 bsc 0.90 C 1.30 0.90 C 1.45 0.09 C 0.15 note 3 0.20 bsc 0.35 C 0.55 ref pin one id note: 1. dimensions are in millimeters 2. drawing not to scale 3. dimensions are inclusive of plating 4. dimensions are exclusive of mold flash and metal burr 5. mold flash shall not exceed 0.254mm 6. package eiaj reference is sc-74a (eiaj) attention: original sot23-6l package. most sot23-6l products converted to thin sot23 package, drawing # 05-08-1636 after approximately april 2001 ship date 3.85 max 0.62 max 0.95 ref recommended solder pad layout per ipc calculator 1.4 min 2.62 ref 1.22 ref
lt1933 20 1933fe linear technology corporation 1630 mccarthy blvd., milpitas, ca 95035-7417 (408) 432-1900 fax: (408) 434-0507 www.linear.com ? linear technology corporation 2007 lt 0409 rev e ? printed in usa related parts typical application part number description comments lt1074/lt1074hv 4.4a i out , 100khz, high ef? ciency step-down dc/dc converter v in : 7.3v to 45v/64v, v out(min) = 2.21v, i q = 8.5ma, i sd = 10a, dd-5/dd-7, to220-5/to220-7 packages lt1076/lt1076hv 1.6a i out , 100khz, high ef? ciency step-down dc/dc converter v in : 7.3v to 45v/64v, v out(min) = 2.21v, i q = 8.5ma, i sd = 10a, dd-5/dd-7, to220-5/to220-7 packages lt1676 60v, 440ma i out , 100khz, high ef? ciency step-down dc/dc converter v in : 7.4v to 60v, v out(min) = 1.24v, i q = 3.2ma, i sd = 2.5a, s8 package lt1765 25v, 2.75ma i out , 1.25mhz, high ef? ciency step-down dc/dc converter v in : 3v to 25v, v out(min) = 1.2v, i q = 1ma, i sd = 15a, s8, tssop16e packages lt1766 60v, 1.2a i out , 200khz, high ef? ciency step-down dc/dc converter v in : 5.5v to 60v, v out(min) = 1.2v, i q = 2.5ma, i sd = 25a, s8, tssop16/tssop16e packages lt1767 25v, 1.2a i out , 1.25mhz, high ef? ciency step-down dc/dc converter v in : 3v to 25v, v out(min) = 1.2v, i q = 1ma, i sd = 6a, s8, ms8/ms8e packages lt1776 40v, 550ma i out , 200khz, high ef? ciency step-down dc/dc converter v in : 7.4v to 40v, v out(min) = 1.24v, i q = 3.2ma, i sd = 30a, s8, n8, s8 packages lt1940 25v, dual 1.4a i out , 1.1mhz, high ef? ciency step-down dc/dc converter v in : 3.6v to 25v, v out(min) = 1.25v, i q = 3.8ma, i sd < 30a, tssop16e package lt1956 60v, dual 1.2a i out , 500khz, high ef? ciency step-down dc/dc converter v in : 5.5v to 60v, v out(min) = 1.2v, i q = 2.5ma, i sd = 25a, tssop16/tssop16e packages lt1976 60v, dual 1.2a i out , 200khz, high ef? ciency step-down dc/dc converter with burst mode ? v in : 3.3v to 60v, v out(min) = 1.2v, i q = 100a, i sd < 1a, tssop16e package lt3010 80v, 50ma, low noise linear regulator v in : 1.5v to 80v, v out(min) = 1.28v, i q = 30a, i sd < 1a, ms8e package lt3407 dual 600ma i out , 1.5mhz, synchronous step-down dc/dc converter v in : 2.5v to 5.5v, v out(min) = 0.6v, i q = 40a, i sd < 1a, ms10e package lt3412 2.5a i out , 4mhz, synchronous step-down dc/dc converter v in : 2.5v to 5.5v, v out(min) = 0.8v, i q = 60a, i sd < 1a, tssop16e package ltc3414 4a i out , 4mhz, synchronous step-down dc/dc converter v in : 2.3v to 5.5v, v out(min) = 0.8v, i q = 64a, i sd < 1a, tssop20e package lt3430/lt3431 60v, 2.75a i out , 200khz/500khz, synchronous step-down dc/dc converter v in : 5.5v to 60v, v out(min) = 1.2v, i q = 2.5ma, i sd = 30a, tssop16e package burst mode is a registered trademark of linear technology corporation. 2.5v step-down converter v in 3.6v to 36v off on c3 0.47f d2 l1 15h r2 10k r1 10.5k c1 22f 1933 ta03 c2 2.2f v out 2.5v/500ma v in boost gnd fb shdn sw lt1933 d1

▲Up To Search▲

Price & Availability of LT1933ES6TRPBF

	To Download LT1933ES6TRPBF Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .